Effect of moisture content on the physical and aerodynamics properties of cashew nut

Authors

  • J. Isa Department of Agricultural and Environmental Engineering, Federal University of Technology, Akure, Nigeria
  • M. A. Aderotoye Department of Agricultural and Environmental Engineering, Federal University of Technology, Akure, Nigeria

Keywords:

Cashew nut, moisture content, physical properties, aerodynamics properties, terminal velocity

Abstract

Physical and aerodynamics properties of nuts and other seeds are often needed for the design of cleaning, de-hulling, separating and other processing equipment and machineries. Physical properties (Sizes, surface area, sphericity index, roundness, mass, volume, angle of repose, coefficient of friction and terminal velocity) and Gravimetric properties (bulk density, true density and porosity measurements) were determined for cashew nuts using standard techniques in the moisture content range of 4.0% to 10.8% wet basis. The static coefficient of friction of the cashew nut was determined on four different materials, namely, wood, mild steel, stainless steel and galvanized sheet while the terminal velocity was measured using vertical air tunnel. The average length, thickness, width, equivalent diameter, sphericity and volume for cashew nuts were 30.58 mm, 17.16mm, 24.53mm, 23.25 mm, 76.28% and 20.7 mm3 respectively. The terminal velocity increased from 2.31m /s to 2.54m/s as the moisture content increased. The co-efficient of friction on various surfaces increased with increase in moisture content. Plastic as a surface for sliding offered the maximum friction followed by mild steel, stainless steel and galvanized sheet at 4%MCw.b, while at moisture content of 6.1, 8.5 and 10.8%w.b mild steel offered the maximum friction. These findings provided useful data for the suitable design and fabrication of processing machines such as sorting, grading, grinding, drying and packaging and will also provide useful knowledge for industrial processing of cashew nut.

References

Adetunmobi, 0 . (2001). Nigerian cashew industry: Curbing the waste. A paper delivered at the preconferencemeeting of the National Cashew Association of Nigeria . Lagos, Nigeria.

Agnoloni, A. and Giuliani, F. (1977). Cashew Nut Cultivation. Ministry of Foreign Affairs, lnstituto Agronomico per Oltremare, Italy.

Ajav, E.A. (1996).The design and testing ofa low cost cashew nut cracker for peasant farmers. Tropical Agric., 73(3), 180- 186.

Akinwale, T.O. (1996). Cashew utilization: CRIN Experience. Proc. National Workshop 'Cashew Production Technology,' March 26-29, Cocoa Research Institute of Nigeria (CRIN), Ibadan, Nigeria.

Al-Mahasneh, M.A. , and Rababah,T. M. (2007). Effect of Moisture Content on Some Physical Properties of Green Wheat. J Food Eng, 79, 1467- 1473

Azam-Alli, S.H. and Judge, E.C. (2001). Small Scale Cashew Nut Processing. Intermediate Technology Development GroupFAO,Rome.

Baryeh, E. A.and Mangope, B. K. (2002). Some physical properties of QP- 38 variety pigeon pea. J Food Eng, 56, 59-65

BisanaB.B. andLaxamanaN.B. (1998). Utilizationofcashew shell residue for charcoal briquettes and activated carbon production. FPRDI-Joumal, 24(2), 25-37.

Coskun, M. B., Yalcin, land Ozarslan C. (2006) Physical properties of sweet com seed (Zea mays saccharata) Journal of Food and Engineering 74:523-548.

Dharmarajah, A.H. and Cleaspy J.L. (1986). Predicting the expansion behavior of filter media. Journal AWWA, 66- 76.

Djarwant o, A.S . and Abdurroh i m, S. (2000). Wood preservation technology to lenghten its service life. Buletin Penelitian dan Pengembangan Kehutanan. Indonesia, 1 ( 2), I 59-172. Overseas Development Natural Resources Institute Press, Chatham, Kent, UK.

Dutta, S.K; Nema V.K. and Bharwaj, R.K. (1988). Thermal properties of gram. J. Agric. Eng.Res. 39(4). pp: 269 -75. Engineering. 96(1) 57-63.

FAO (2006). Statis tics. Cashew. www.uga.edu /frui t/cashew.html. Accessed on June 14

Gezer, I., Hacis eferogullari, H., and Demir, F. (2002). Some physical properties of Hacihaliloglu apricot pit and its kernel. Journal ofFood Engineering, 56: 49-57.

Gibbon, D. and Pain, A. (1985).Crops of the Drier Regions of the Tropics. Longman Press, London, UK, 23-25.

Gupta, R. K., and Das. S. K. (1997). Physical properties of sunflower seeds. Journal of Agricultural Engineering Research, 56(1): 49-57, 66:1- 8.

Heidarbeigi , k., Ahmadi, H., Khaeiralipour, k., and Tabatabaeefar, A. (2009). Some physical and mechanical properties of hhinkuk.pakj nut, 8(1), 74- 77

Intermediate Technology Development Group, (2005). Technical Brief- Cashew nut processing. Knowledge and Information services. The Schumacher Center for Technology Development. Warwickshire, UK.

Jain, R.K. and Sivala K. (1997). Development of a cashew nut sheller. J. Food Eng., 32(339-345).

Kashaninejad, M., L.G.Tabil, A. Mortazavi and A. Safe Kordi, (2003) . Effect of drying methods on the quality of pistachio nuts. Drying Technol., 21: 821- 838

Konak M., Carman K. and Aydin, C. (2002). Physical properties of chick pea seeds. Biosystems Engineering, 82: 73- 78.

Mohsenin, N.N. (1978). Physical Properties of Plant and Animal Materials. Gordon and Breach Pub!. Inc., New York.

Nimkar P.M and Chattopadhyay, P.K. (2001) . Some physical properties of green gram. Journal of Agricultural Engineering Research , 80: 183- 189.

Nouwligbeto, F.D. and Jerome, A. (2003). African cashew nut in a harsh world Jnfosud-Syfia publication. No 196 January­ February.

O'Farrell P., Blackie S., and Chacko E., (2006). The New Rural Industries: A Handbook for Farmers and Investors. Rural Industries Res . Devel. Corp. (RIRDC). Australia. http :// www .rirdc .gov.au/pub /handbook /casew.html . June I 4, 2006.

Ogunsina, B.S. and Odugbenro, P.O. (2005). Prospects for cashew nut processing industry in Nigeria. Landwards. Institution of Agricultural Engineers Journal, UK. 60(4) 2-6.

Ohler, J.G. (1979).Cashew Growing: Tropical Abstracts. Cashew Dept. Agr ic. Res., Royal Tropical Institute Press, Amsterdam.

Olunloyo O.A. (1996).Cashew and its potent iali ties . Proc. National Workshop 'Cashew Production Technology,' March 26-29, Cocoa Research Institute of Nigeria (CRIN), Ibadan, Nigeria.

Omobuwajo, T.O., Akande, E.A and Sanni, L.A. (1999). Selected physical, mechanical and aerodynamic properties of Africa breadfruit (Treculia africana) seeds. J Food Eng. 40: 241- 244.

Omobuwajo, T.O ., Sa nni, L.A. and Olajide, J.O. (2000) Physical properties of ackee apple (Blighia sapida) seeds. J Food Eng. 45: 43-4 8.

Ozarslan,C., (2002). Physical properties of cotton seed. Biosystems Eng.83, 2: 169-174.

Sacilik, K., Ozturk, Rand Keskin R. (2003). Some physical properties of hemp seed. Biosystems Engineering, 86: 191-198.

Scheidegger A.E. (1960). The physics of flow through porous media. Univeristy Toronto Press.

Singh K.K., and Goswami T.K., (1996). Physical properties of Cumin seed. Journal of Agricultural Engineering Research, 64: 93- 98.

Suthar S.H. and Das S.K. (1996). Some physical properties of karingda [Citrullus lanatus (Thumb) seeds. Journal of Agricultural Engineering Research , 65: 15-22.

Tabatabaeefar, A. (2003). Moisture - dependent physical properties of wheat.inter Agrophysics, 17, 207- 211 .

Tavakoli, H., Rajabipo ur, A., and Mohtasebi , S. S. (2009) . Moisture-dependant some engineering properties of soybean grains. Agr Eng: the CIGR. Ejournal, Manuscript 11 10, vol.XI

Thivavarvongs T., Okamoto T., and Kitani 0. (1995).Development of compact sized cashew nutshelling machinery (Part 1). Synthesis of effective manual and semi-automatic shelling methods. J. Japanese Soc. Agric. Machi nery, 57(2), 57-76.

Zenz, F.A. and Othmer, D.F. (1960). Fluidi zation and fluid­ particle systems. Reinhold Publishing Corporation, New York.

Downloads

Published

2019-05-05